Fast Car

The sequence of execution: 1.Neobhodimo warm up the engine. 2.Zatem unscrew the drain plug on sex trafficking. Then set the container for collecting oil and unscrew the plug. 3.Dozhdites until all the oil will flow down, pushing capacity if needed. 4.Protrite cover and if necessary change the sealing washer. Wipe the area around the hole and tighten the cap. 5.Pod oily filter set capacity for oil. 6.Pri using tools remove the oily filter. 7.Dalee clean place to install the filter, lubricate oil seal for the filter. Secure it and then tighten by hand. 8.Zaleyte oil and check the dipstick. 9.Zapustite engine and make sure that no leakage around the Pancake filter and plugs the drain. Note: On models where the turbocharger is installed is not recommended to raise the engine speed until the indicator light goes off oil pressure. Check brake pads front brake on the Audi 100 In order to check the brake pads, need to raise the front of the car. Then remove the front wheels. The thickness of the brake pads can be seen through a hole on the front calipers. To define more precisely of wear, they must be removed and cleaned. If the thickness of some stocks fell more than the permissible value, then they need to change on both wheels. Replacing spark plugs in the Audi execution sequence: 1.Neobhodimo unscrew the screws and remove the cover from the valve cover. 2.Dalee mark the high voltage wires and disconnect them from the spark plugs. 3.Protrite area around the spark plug, and slowly at the special tool to remove the candle. 4.Izmerte spark gap spark plug with a special tool or set of probes. 5.Podognite its tip, thereby otreguliruete it. 6.Ustanovite spark plug in place. To facilitate their work, put a short pipe at the candle. This segment will serve as a universal joint and do not give a groove crank. Removing Pancake pan Audi execution sequence: - In the first lift and secure the front of the car - next step is to remove the lower guard engine and then pour the engine oil - Good fix the engine on the lift - Remove the front cover of the gearbox - Next you need skurit lower engine mount nuts - under the front suspension crossmember install the jack, loosen the screw and slightly lower crossmember - Remove the pan bolts - Remove the pan. Installation: Before installing the need to clean the surface of the pan and cylinder block, and then install a new gasket. Setting the tray is carried out in reverse order of removal.

At the back of any car there will always be minor imperfections: minor dents, scratches or shallow inconspicuous chipped. On some cars they are small, almost imperceptible, on the other boldly striking. Any defects do not appear themselves. They may be due to a small accident, which happened to be your car, or carelessness buyer, scratched his truck, parked a large store. Or simply - your four-wheeled friend of old, and from the prolonged use of dye its faded. Someday, every car owner has to hire the services of service center. Price body repair in the service often unpleasant high. Does this situation an alternative? Rejoice - there! First choice: if you have an insurance case, requires the company to which your pet is insured, pay the refurbishment of the body. Second: If the case is not insurance or a car is not insured, still have to pay out of pocket. And finally, three: paint cars on their own. It's no secret that the expertise of the official service repair Audi road. Not all owners can afford the pleasure of paying for maintenance and repair their own vehicle in a specialized service. In this situation the best option, do all the feasible work on their own. For example, it is actually very do local repair body panels - paint it. This will bring you along with the savings funds enjoy a long and laborious work in his garage. And, unfortunately, the output may not turn out quite what was expected. Therefore, choosing a handwritten version of the painting, weigh the pros and cons. Indeed, it may be that the correction of handwritten blunders will have to spend more than "once in service." In order to avoid any visible repairs, special attention should be paid to the preparation of the working surface of the restored area, carefully select the type and shade of paint. In carrying out the work necessary to strictly follow the rules of painting: the working area sand sandpaper, then degrease it with gasoline. Remember, the more paint is applied in three layers of thickness 70 - 120 microns each. If you still have decided on a superficial repair of Audi with their own hands, do not forget that you're going to paint only the damaged section, not the entire car. Consequently, the remaining surface of the machine must be carefully sealed to hit the paint. To do this, use paper, cloth, masking tape, or roll the patch out of the shop. You can bring a mixture of (water + chalk + glycerin + dextrin) and cover it is not processed surface areas. Periodic wetting the floor with water will help get rid of dust in the air. Necessary to check the compressor to the air contained in it was free of impurities of water or mineral oil. If necessary, add paint thinner and thinner, that you will achieve the desired consistency dye solution. By the way, varnish, paint, putty, primer should be well stirred, after removing from the surface film. Better use for this clean wooden stick or paddle. The resulting solution strain to avoid the presence of lumps. For the repair of Audi Olroud is a special rule: for each subsequent layer of paint should be more liquid.