Sunday, June 2, 2013
Replacing the filter and engine oil Car Audi 100
The sequence of execution: 1.Neobhodimo warm up the engine. 2.Zatem unscrew the drain plug on sex trafficking. Then set the container for collecting oil and unscrew the plug. 3.Dozhdites until all the oil will flow down, pushing capacity if needed. 4.Protrite cover and if necessary change the sealing washer. Wipe the area around the hole and tighten the cap. 5.Pod oily filter set capacity for oil. 6.Pri using tools remove the oily filter. 7.Dalee clean place to install the filter, lubricate oil seal for the filter. Secure it and then tighten by hand. 8.Zaleyte oil and check the dipstick. 9.Zapustite engine and make sure that no leakage around the Pancake filter and plugs the drain. Note: On models where the turbocharger is installed is not recommended to raise the engine speed until the indicator light goes off oil pressure. Check brake pads front brake on the Audi 100 In order to check the brake pads, need to raise the front of the car. Then remove the front wheels. The thickness of the brake pads can be seen through a hole on the front calipers. To define more precisely of wear, they must be removed and cleaned. If the thickness of some stocks fell more than the permissible value, then they need to change on both wheels. Replacing spark plugs in the Audi execution sequence: 1.Neobhodimo unscrew the screws and remove the cover from the valve cover. 2.Dalee mark the high voltage wires and disconnect them from the spark plugs. 3.Protrite area around the spark plug, and slowly at the special tool to remove the candle. 4.Izmerte spark gap spark plug with a special tool or set of probes. 5.Podognite its tip, thereby otreguliruete it. 6.Ustanovite spark plug in place. To facilitate their work, put a short pipe at the candle. This segment will serve as a universal joint and do not give a groove crank. Removing Pancake pan Audi execution sequence: - In the first lift and secure the front of the car - next step is to remove the lower guard engine and then pour the engine oil - Good fix the engine on the lift - Remove the front cover of the gearbox - Next you need skurit lower engine mount nuts - under the front suspension crossmember install the jack, loosen the screw and slightly lower crossmember - Remove the pan bolts - Remove the pan. Installation: Before installing the need to clean the surface of the pan and cylinder block, and then install a new gasket. Setting the tray is carried out in reverse order of removal.
Saturday, May 4, 2013
How to Install a Cone Filter in an Audi A4
1. Open your hood and locate the air filter box and intake tube. Turbo models will feature a heftier intake that attaches to the turbocharger, while naturally aspirated engines have intake that attaches to only the throttle body.
2. Disconnect the electrical wiring, hoses and mass air flow meter that attach to the factory intake tube and set aside for use with the new intake system. Unfasten the hardware that holds the intake tube in place and remove slowly, careful not to spill any debris. If necessary, use a flat-head screwdriver to assist you in removing the intake tube.
3. Unscrew the bolts that hold the stock air filter box into place. Remove this factory intake box completely and dispose of it properly, as you will not need the filter or its housing box for the new install.
4. Check the new intake tube and count the number of holes that are drilled into the side. If there are more holes than hoses that attached to the old setup, plug the unnecessary holes with the grommets that came with your intake kit.
5. Attach the new intake tube to your A4 directly as the old one was removed. This part will mimic the old intake tube in design and functionality, while the filter itself will be positioned differently and provide better performance. Secure the intake tube with the silicone coupling that came with your cold air intake kit. There should also be a clamp ring that came with your kit to hold the silicone coupling and intake tube into place.
6. Attach the downward piece of the intake tubing system to the newly installed tube from Step 5. By this point, the intake tube should extend to the front of the engine bay and underneath the front of the car. The cold air will come in through the bottom of the front side of the vehicle, increasing horespower and fuel efficiency in your Audi A4.
7. Spray down the new air filter with the necessary lubricant before installing. Position the cone air filter that was provided in the cold air intake kit onto the downward intake tube. Tighten the clamp fitted around the cone filter to secure into place. Reconnect any remaining hoses and wiring that were removed at this time.
Friday, May 3, 2013
How to Replace a Cabin Air Filter in a BMW 3 Series
1. Purchase the correct replacement filter. BMW uses a charcoal activated filter for its 3 Series. You may be able to purchase an aftermarket substitute at an automotive parts store, but you can purchase a factory replacement at your BMW dealer.
2. Shut the engine off and pull the hood release. Locate the cabin air filter cover in the rear part of the engine compartment, right beneath the windshield (it extends to the width of the engine bay).
3. Twist the three fasteners counterclockwise to unhook the cabin air filter cover. Once the fasteners are loosened, pull the entire cover up and set to the side.
4. Pull the old filter out of the compartment. Its clearly visible with the cover removed. Inspect the compartment for foreign items and debris; remove them, if applicable.
5. Insert the replacement filter into the compartment. Position the cabin air filter cover back in place and turn the three fasteners clockwise to secure it.
Tuesday, April 30, 2013
How to Replace the Cabin Air Filter on Audi A3
1. Remove the cowling cover from rear of the engine compartment that covers the firewall. The cowling is secured with screws to the frame of the vehicle. Use a screwdriver to remove the screws and set the cowling off to the side.
2. Locate the cabin air filter compartment on the left side of the firewall, next to the heater fan. The air filter is 6-by-9 inches in size and 2 inches thick. It should be mounted vertically against the firewall. Remove the cover by using a screwdriver to lightly unfasten the lid.
3. Remove the cabin air filter from the compartment. Clean out the compartment by vacuuming out any dust. Wipe it down with a clean damp cloth.
4. Replace the old cabin air filter with the new filter and make sure filter is seated properly. Secure the lid on the filter compartment, making sure the pins snap into place.
5. Reattach the cowling cover over the firewall with screws. Remove all tools from the engine compartment.